I have a 2002 wrx that starts to leak coolant where the radiator upper hose
is clamped to the radiator, after driving the car for 30 minutes on a
freeway. The coolant would drip on to the radiator and vaporize, causing a
burnt odor detectable from inside the car. This problem existed ever since I
bought the car.

The solution could be as simple as adjusting the hose clamp. But I want to
be sure it is not a more serious problem. Is it normal for the pressure in
the radiator to increase after driving 30 minutes? And when the pressure
increases, it is supposed to force some coolant into the reservoir (the
metal can with a radiator cap), then into the coolant overflow tank, right?

john wrote:

> The solution could be as simple as adjusting the hose clamp. But I want to
> be sure it is not a more serious problem. Is it normal for the pressure in

Hi,

There's an old saying, "When you hear hoof beats, think of horses before
zebras."

Yes, it's normal for pressure to build up a little in time, and yes,
that pressure should be vented to the overflow tank, but let's remember
that Nature generally prefers the course of least energy expenditure, so
your coolant will find and try to escape from any tiny leakage point
BEFORE going to the trouble of traveling to the overflow tank. So:

Step 1--check the clamps and tighten as required...

Step 2--if that doesn't work, replace the hose. If it's the original,
it's very likely getting stiff and may not seal well. While the hose is
off, inspect the connection to make sure it's clean (no buildup of scale
and such) and not damaged. If it is, repair as required (as long as the
connections are smooth, I generally don't use sealer on hoses, but IF
there's some roughness due to corrosion, etc., one may benefit from a
sealer between the connection and hose. I've tried several that work,
but usually go w/ Permatex High Tack if the parts store stocks it.) If
you replace ONE hose, seriously consider doing them ALL at the same
time. It will probably mean time and money saved later...

Step 3--if neither of the above work, think zebras and start looking for
more complicated causes...

Good luck!

Rick

Rick Courtright wrote:

> john wrote:
>
>
>>The solution could be as simple as adjusting the hose clamp. But I want to
>>be sure it is not a more serious problem. Is it normal for the pressure in
>
>
> Hi,
>
> There's an old saying, "When you hear hoof beats, think of horses before
> zebras."
>
> Yes, it's normal for pressure to build up a little in time, and yes,
> that pressure should be vented to the overflow tank, but let's remember
> that Nature generally prefers the course of least energy expenditure, so
> your coolant will find and try to escape from any tiny leakage point
> BEFORE going to the trouble of traveling to the overflow tank. So:
>
> Step 1--check the clamps and tighten as required...
>
> Step 2--if that doesn't work, replace the hose. If it's the original,
> it's very likely getting stiff and may not seal well. While the hose is
> off, inspect the connection to make sure it's clean (no buildup of scale
> and such) and not damaged. If it is, repair as required (as long as the
> connections are smooth, I generally don't use sealer on hoses, but IF
> there's some roughness due to corrosion, etc., one may benefit from a
> sealer between the connection and hose. I've tried several that work,
> but usually go w/ Permatex High Tack if the parts store stocks it.) If
> you replace ONE hose, seriously consider doing them ALL at the same
> time. It will probably mean time and money saved later...
>
> Step 3--if neither of the above work, think zebras and start looking for
> more complicated causes...
>
> Good luck!
>
> Rick


Excellent advice.

AFTER doing the above, some other 'horses' could be the radiator cap and
the thermostat - though if the temperature gauge indicates normal, the
t'stat is likely OK.

Carl


--
to reply, change ( .not) to ( .net)